diff --git a/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts
index 25fb048..c488aaa 100644
--- a/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts
+++ b/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts
@@ -59,6 +59,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -91,9 +102,21 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
+		clocks = <&ccu CLK_OUTA>;
+		clock-names = "ext_clock";
 	};
 };
 
+&ahci {
+	ahci-supply = <&reg_dldo4>;
+	phy-supply = <&reg_eldo3>;
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -118,6 +141,16 @@
 	};
 };
 
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &i2c0 {
 	status = "okay";
 
@@ -134,8 +167,7 @@
 &mmc0 {
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
-	cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
-	cd-inverted;
+	cd-gpios = <&pio 7 13 GPIO_ACTIVE_LOW>; /* PH13 */
 	status = "okay";
 };
 
@@ -166,6 +198,11 @@
 	status = "okay";
 };
 
+&pio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&clk_out_a_pin>;
+};
+
 &reg_aldo2 {
 	regulator-always-on;
 	regulator-min-microvolt = <2500000>;
@@ -220,18 +257,68 @@
 	regulator-name = "vcc-wifi-io";
 };
 
+/*
+ * Our WiFi chip needs both DLDO2 and DLDO3 to be powered at the same
+ * time, with the two being in sync, to be able to meet maximum power
+ * consumption during transmits. Since this is not really supported
+ * right now, just use the two as always on, and we will fix it later.
+ */
+
 &reg_dldo2 {
+	regulator-always-on;
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
 	regulator-name = "vcc-wifi";
 };
 
+&reg_dldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-2";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	regulator-name = "vdd2v5-sata";
+};
+
+&reg_eldo3 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vdd1v2-sata";
+};
+
+&tcon_tv0 {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };
 
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pg_pins>, <&uart3_rts_cts_pg_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&ccu CLK_OUTA>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_dldo2>;
+		vddio-supply = <&reg_dldo1>;
+		device-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		/* TODO host wake line connected to PMIC GPIO pins */
+		shutdown-gpios = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */
+		max-speed = <1500000>;
+	};
+};
+
 &usbphy {
 	usb1_vbus-supply = <&reg_vcc5v0>;
 	usb2_vbus-supply = <&reg_vcc5v0>;
diff --git a/arch/arm/dts/sun8i-r40.dtsi b/arch/arm/dts/sun8i-r40.dtsi
index bd97ca3..06b6858 100644
--- a/arch/arm/dts/sun8i-r40.dtsi
+++ b/arch/arm/dts/sun8i-r40.dtsi
@@ -42,8 +42,10 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun8i-de2.h>
 #include <dt-bindings/clock/sun8i-r40-ccu.h>
 #include <dt-bindings/reset/sun8i-r40-ccu.h>
+#include <dt-bindings/reset/sun8i-de2.h>
 
 / {
 	#address-cells = <1>;
@@ -59,6 +61,7 @@
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
+			clock-accuracy = <50000>;
 			clock-output-names = "osc24M";
 		};
 
@@ -66,7 +69,8 @@
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <32768>;
-			clock-output-names = "osc32k";
+			clock-accuracy = <20000>;
+			clock-output-names = "ext-osc32k";
 		};
 	};
 
@@ -99,12 +103,75 @@
 		};
 	};
 
+	de: display-engine {
+		compatible = "allwinner,sun8i-r40-display-engine";
+		allwinner,pipelines = <&mixer0>, <&mixer1>;
+		status = "disabled";
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 
+		display_clocks: clock@1000000 {
+			compatible = "allwinner,sun8i-r40-de2-clk",
+				     "allwinner,sun8i-h3-de2-clk";
+			reg = <0x01000000 0x100000>;
+			clocks = <&ccu CLK_DE>,
+				 <&ccu CLK_BUS_DE>;
+			clock-names = "mod",
+				      "bus";
+			resets = <&ccu RST_BUS_DE>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		mixer0: mixer@1100000 {
+			compatible = "allwinner,sun8i-r40-de2-mixer-0";
+			reg = <0x01100000 0x100000>;
+			clocks = <&display_clocks CLK_BUS_MIXER0>,
+				 <&display_clocks CLK_MIXER0>;
+			clock-names = "bus",
+				      "mod";
+			resets = <&display_clocks RST_MIXER0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mixer0_out: port@1 {
+					reg = <1>;
+					mixer0_out_tcon_top: endpoint {
+						remote-endpoint = <&tcon_top_mixer0_in_mixer0>;
+					};
+				};
+			};
+		};
+
+		mixer1: mixer@1200000 {
+			compatible = "allwinner,sun8i-r40-de2-mixer-1";
+			reg = <0x01200000 0x100000>;
+			clocks = <&display_clocks CLK_BUS_MIXER1>,
+				 <&display_clocks CLK_MIXER1>;
+			clock-names = "bus",
+				      "mod";
+			resets = <&display_clocks RST_WB>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mixer1_out: port@1 {
+					reg = <1>;
+					mixer1_out_tcon_top: endpoint {
+						remote-endpoint = <&tcon_top_mixer1_in_mixer1>;
+					};
+				};
+			};
+		};
+
 		nmi_intc: interrupt-controller@1c00030 {
 			compatible = "allwinner,sun7i-a20-sc-nmi";
 			interrupt-controller;
@@ -248,23 +315,38 @@
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun8i-r40-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&osc32k>;
+			clocks = <&osc24M>, <&rtc 0>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 		};
 
+		rtc: rtc@1c20400 {
+			compatible = "allwinner,sun8i-r40-rtc",
+				     "allwinner,sun8i-h3-rtc";
+			reg = <0x01c20400 0x400>;
+			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+			clock-output-names = "osc32k", "osc32k-out";
+			clocks = <&osc32k>;
+			#clock-cells = <1>;
+		};
+
 		pio: pinctrl@1c20800 {
 			compatible = "allwinner,sun8i-r40-pinctrl";
 			reg = <0x01c20800 0x400>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
+			clk_out_a_pin: clk-out-a-pin {
+				pins = "PI12";
+				function = "clk_out_a";
+			};
+
 			gmac_rgmii_pins: gmac-rgmii-pins {
 				pins = "PA0", "PA1", "PA2", "PA3",
 				       "PA4", "PA5", "PA6", "PA7",
@@ -312,6 +394,16 @@
 				pins = "PB22", "PB23";
 				function = "uart0";
 			};
+
+			uart3_pg_pins: uart3-pg-pins {
+				pins = "PG6", "PG7";
+				function = "uart3";
+			};
+
+			uart3_rts_cts_pg_pins: uart3-rts-cts-pg-pins {
+				pins = "PG8", "PG9";
+				function = "uart3";
+			};
 		};
 
 		wdt: watchdog@1c20c90 {
@@ -464,6 +556,19 @@
 			#size-cells = <0>;
 		};
 
+		ahci: sata@1c18000 {
+			compatible = "allwinner,sun8i-r40-ahci";
+			reg = <0x01c18000 0x1000>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SATA>, <&ccu CLK_SATA>;
+			resets = <&ccu RST_BUS_SATA>;
+			resets-name = "ahci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+		};
+
 		gmac: ethernet@1c50000 {
 			compatible = "allwinner,sun8i-r40-gmac";
 			syscon = <&ccu>;
@@ -474,8 +579,6 @@
 			reset-names = "stmmaceth";
 			clocks = <&ccu CLK_BUS_GMAC>;
 			clock-names = "stmmaceth";
-			#address-cells = <1>;
-			#size-cells = <0>;
 			status = "disabled";
 
 			gmac_mdio: mdio {
@@ -485,6 +588,213 @@
 			};
 		};
 
+		tcon_top: tcon-top@1c70000 {
+			compatible = "allwinner,sun8i-r40-tcon-top";
+			reg = <0x01c70000 0x1000>;
+			clocks = <&ccu CLK_BUS_TCON_TOP>,
+				 <&ccu CLK_TCON_TV0>,
+				 <&ccu CLK_TVE0>,
+				 <&ccu CLK_TCON_TV1>,
+				 <&ccu CLK_TVE1>,
+				 <&ccu CLK_DSI_DPHY>;
+			clock-names = "bus",
+				      "tcon-tv0",
+				      "tve0",
+				      "tcon-tv1",
+				      "tve1",
+				      "dsi";
+			clock-output-names = "tcon-top-tv0",
+					     "tcon-top-tv1",
+					     "tcon-top-dsi";
+			resets = <&ccu RST_BUS_TCON_TOP>;
+			#clock-cells = <1>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon_top_mixer0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					tcon_top_mixer0_in_mixer0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&mixer0_out_tcon_top>;
+					};
+				};
+
+				tcon_top_mixer0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					tcon_top_mixer0_out_tcon_lcd0: endpoint@0 {
+						reg = <0>;
+					};
+
+					tcon_top_mixer0_out_tcon_lcd1: endpoint@1 {
+						reg = <1>;
+					};
+
+					tcon_top_mixer0_out_tcon_tv0: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&tcon_tv0_in_tcon_top_mixer0>;
+					};
+
+					tcon_top_mixer0_out_tcon_tv1: endpoint@3 {
+						reg = <3>;
+						remote-endpoint = <&tcon_tv1_in_tcon_top_mixer0>;
+					};
+				};
+
+				tcon_top_mixer1_in: port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+
+					tcon_top_mixer1_in_mixer1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&mixer1_out_tcon_top>;
+					};
+				};
+
+				tcon_top_mixer1_out: port@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+
+					tcon_top_mixer1_out_tcon_lcd0: endpoint@0 {
+						reg = <0>;
+					};
+
+					tcon_top_mixer1_out_tcon_lcd1: endpoint@1 {
+						reg = <1>;
+					};
+
+					tcon_top_mixer1_out_tcon_tv0: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&tcon_tv0_in_tcon_top_mixer1>;
+					};
+
+					tcon_top_mixer1_out_tcon_tv1: endpoint@3 {
+						reg = <3>;
+						remote-endpoint = <&tcon_tv1_in_tcon_top_mixer1>;
+					};
+				};
+
+				tcon_top_hdmi_in: port@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+
+					tcon_top_hdmi_in_tcon_tv0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon_tv0_out_tcon_top>;
+					};
+
+					tcon_top_hdmi_in_tcon_tv1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&tcon_tv1_out_tcon_top>;
+					};
+				};
+
+				tcon_top_hdmi_out: port@5 {
+					reg = <5>;
+
+					tcon_top_hdmi_out_hdmi: endpoint {
+						remote-endpoint = <&hdmi_in_tcon_top>;
+					};
+				};
+			};
+		};
+
+		tcon_tv0: lcd-controller@1c73000 {
+			compatible = "allwinner,sun8i-r40-tcon-tv";
+			reg = <0x01c73000 0x1000>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_TCON_TV0>, <&tcon_top 0>;
+			clock-names = "ahb", "tcon-ch1";
+			resets = <&ccu RST_BUS_TCON_TV0>;
+			reset-names = "lcd";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon_tv0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					tcon_tv0_in_tcon_top_mixer0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon_top_mixer0_out_tcon_tv0>;
+					};
+
+					tcon_tv0_in_tcon_top_mixer1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&tcon_top_mixer1_out_tcon_tv0>;
+					};
+				};
+
+				tcon_tv0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					tcon_tv0_out_tcon_top: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&tcon_top_hdmi_in_tcon_tv0>;
+					};
+				};
+			};
+		};
+
+		tcon_tv1: lcd-controller@1c74000 {
+			compatible = "allwinner,sun8i-r40-tcon-tv";
+			reg = <0x01c74000 0x1000>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_TCON_TV1>, <&tcon_top 1>;
+			clock-names = "ahb", "tcon-ch1";
+			resets = <&ccu RST_BUS_TCON_TV1>;
+			reset-names = "lcd";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon_tv1_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					tcon_tv1_in_tcon_top_mixer0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon_top_mixer0_out_tcon_tv1>;
+					};
+
+					tcon_tv1_in_tcon_top_mixer1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&tcon_top_mixer1_out_tcon_tv1>;
+					};
+				};
+
+				tcon_tv1_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					tcon_tv1_out_tcon_top: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&tcon_top_hdmi_in_tcon_tv1>;
+					};
+				};
+			};
+		};
+
 		gic: interrupt-controller@1c81000 {
 			compatible = "arm,gic-400";
 			reg = <0x01c81000 0x1000>,
@@ -495,6 +805,50 @@
 			#interrupt-cells = <3>;
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
+
+		hdmi: hdmi@1ee0000 {
+			compatible = "allwinner,sun8i-r40-dw-hdmi",
+				     "allwinner,sun8i-a83t-dw-hdmi";
+			reg = <0x01ee0000 0x10000>;
+			reg-io-width = <1>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_HDMI0>, <&ccu CLK_HDMI_SLOW>,
+				 <&ccu CLK_HDMI>;
+			clock-names = "iahb", "isfr", "tmds";
+			resets = <&ccu RST_BUS_HDMI1>;
+			reset-names = "ctrl";
+			phys = <&hdmi_phy>;
+			phy-names = "hdmi-phy";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				hdmi_in: port@0 {
+					reg = <0>;
+
+					hdmi_in_tcon_top: endpoint {
+						remote-endpoint = <&tcon_top_hdmi_out_hdmi>;
+					};
+				};
+
+				hdmi_out: port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		hdmi_phy: hdmi-phy@1ef0000 {
+			compatible = "allwinner,sun8i-r40-hdmi-phy";
+			reg = <0x01ef0000 0x10000>;
+			clocks = <&ccu CLK_BUS_HDMI1>, <&ccu CLK_HDMI_SLOW>,
+				 <&ccu 7>, <&ccu 16>;
+			clock-names = "bus", "mod", "pll-0", "pll-1";
+			resets = <&ccu RST_BUS_HDMI0>;
+			reset-names = "phy";
+			#phy-cells = <0>;
+		};
 	};
 
 	timer {
diff --git a/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts
index 35859d8..bf97f62 100644
--- a/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -95,7 +95,7 @@
 &i2c0 {
 	status = "okay";
 
-	axp22x: pmic@68 {
+	axp22x: pmic@34 {
 		compatible = "x-powers,axp221";
 		reg = <0x34>;
 		interrupt-parent = <&nmi_intc>;